| product description: |
The first prototype of the MAZ-537 was built in 1958, and the series model went into production in 1960. The engine used in the new car can output 525 horsepower at a speed of 2100rpm, which was amazing at the time. Only tanks and armored vehicles were equipped with such a powerful engine. The fuel system, cooling system and lubrication system had to be redesigned. , the engine compartment is covered by steel plates. These changes and the strengthened chassis make the weight of the car reach 21.6 tons (with a trailer up to 87 tons) and can tow a 50-ton vehicle.
The first batch of MAZ-537 was manufactured in Minsk, and by 1964 it was transferred to the factory in Kurgan to produce together with MAZ-535.
Overall length: 8.960 meters Overall width: 2.855 meters Overall height: 2.880 meters
Power: 525 hp Top speed: 55-60 km/h Road trip: 650 km
| product number | 07195 |
| product name | MAZ-537G late model (with MAZ/ChMZAP-5247G semi-trailer) |
| barcode | 9580208071954 |
| Product ratio | 1:72 |
| product type | Plastic Model Armor Kit |
| model size | Length: 322mm Width: 46mm |
| total number of parts | 150+ |
| metal parts | n/a |
| etched parts | n/a |
| film | n/a |
| resin parts | n/a |
| Total number of offset plates | 5 sprues , cab , frame and tires |
| Announcement date | 2023-03 |
| more description | The kit consists of over 150 parts -rubber tires |
| product description: |
The development plan of the E-100 super-heavy tank is to try out two prototypes and then choose a production equipment from them. One of them uses a 150mm KwK44 gun, and the other uses a newly designed turret and a 128mm KwK44 gun. The plan started in June 1943, and went smoothly until the end of 1944, but was ordered to be suspended by Hitler, leaving only three technicians to continue the work. By the end of the war they had almost finished the chassis, but neither of the two planned turrets could be built. The British army discovered and seized it, and it was discarded after being transported to the UK for research.
Weight: 140 t Crew: 5 Engine: Maybach HL234 Top speed:40km/h
Maximum Travel: 120 km Overall Length: 10.27 m Overall Width: 4.48 m Overall Height:3.29m
arms:128 mmKwK 44 ,7.92 mmMG34
| product number | 09586 |
| product name | E-100 anti-aircraft tank (equipped with “Rhine Daughter” I rocket) |
| barcode | 9580208095868 |
| Product ratio | 1:35 |
| product type | Plastic Model Armor Kit |
| model size | Length: 253.6mm Width: 128mm |
| total number of parts | 470+ |
| metal parts | n/a |
| etched parts | 1 piece |
| film | n/a |
| resin parts | n/a |
| Total number of offset plates | 16 sprues , upper hull , lower hull and rubber tracks |
| Announcement date | 2023-03 |
| more description | The kit consists of over 470 parts >the kit w/refined detail >multi-slide molded lower hull and upper hull >rubber tracks >photo etched parts included |
| product description: |
The destroyer leader “Tashkent”January 11, 1935Construction started in Italy,November 28, 1937into the water,October 22, 1939Accepted into service by the USSR. The design of the “Tashkent” was unusually avant-garde at the time. It was one of the few large ships with a speed of more than 40 knots during World War II. After the transformation in 1942, its firepower was even upgraded to the level of a light cruiser.
During World War II, her main mission was as a transport ship for personnel and supplies. Among the Soviet ships transporting supplies to Sevastopol, the “Tashkent” is quite legendary, and even the Germans know its name. There were more than 90 air strikes, and the German army dropped more than 400 bombs and fired 10 torpedoes on it.
After the “Tashkent” was withdrawn to the Novorossiysk naval base, it was completely blown up on the slipway in an air strike on July 2. It was salvaged in 1944 and was demolished in 1945 because it had no repair value.
| product number | 06747 |
| product name | Russian “Tashkent” destroyer 1942 |
| barcode | 9580208067476 |
| Product ratio | 1:700 |
| product type | Plastic Model Warship Kit |
| model size | Length: 199.6mm Beam: 19.6mm |
| total number of parts | 110+ |
| metal parts | n/a |
| etched parts | 1 piece |
| film | n/a |
| resin parts | n/a |
| Total number of offset plates | 4 sprues , hull and deck |
| Announcement date | 2023-03 |
| more description | – hull made from multi-directional slide moulds. -Deck wood pattern finely rendered -Contains engraved name plate -Photo-Etched parts included |
>multi-slide moulded lower hull and upper hull
>rubber tracks
>photo etched parts included
| product description: |
Development of the Z-10 attack helicopter began in the mid-1990s, and a prototype first flew in 2003. The main mission of the Z-10 is anti-armor and battlefield interdiction. It also has certain air combat capabilities.
The Z-10 helicopter has a standard gunship structure, narrow fuselage, and tandem cockpit. The weapons operator is at the front and the pilot is at the rear. The diamond-shaped fuselage section can reduce the radar emission area on the side. All important areas will be protected by armor.
The prototype of the Z-10 uses two Canadian Pratt Whitney PT-6C-67C turboshaft engines with a single power of 1531 horsepower. The aircraft may be equipped with a fly-by-wire system, and other systems include helmet sights and head-up displays, electro-optical devices and forward-looking infrared systems, radar and laser warning receivers, infrared jammers and decoy launch systems.
| product number | 05820 |
| product name | Chinese “Zhi-10” attack helicopter |
| barcode | 9580208058207 |
| Product ratio | 1:48 |
| product type | Plastic Model Aircraft Kit |
| model size | Length: 292.7mm Rotor Diameter: 281mm |
| total number of parts | 140+ |
| metal parts | n/a |
| etched parts | 1 piece |
| film | n/a |
| resin parts | n/a |
| Total number of offset plates | 6 sprues |
| Announcement date | 2023-03 |
| more description | – Detailed fuselage w/accurate design – Finely detailed cockpit – photo-etched parts included |
